Drooni 3D prinditava käpa arendus
Laen...
Kuupäev
2026
Kättesaadavus
Suletud / Closed, korraldus nr. 6-1.MI/147
Autorid
Ajakirja pealkiri
Ajakirja ISSN
Köite pealkiri
Kirjastaja
Eesti Maaülikool
Abstrakt
Käesoleva bakalaureusetöö eesmärk oli uurida 3D prinditava FPV droonikäpa tugevuse ja jäikuse suurendamise võimalusi. Töö käigus projekteeriti kolm droonikäpa varianti: originaalne ristkülikukujulise ristlõikega käpp, I-tala kujulise ristlõikega käpp ning alumiiniumsulamist tugevdusribaga käpp. Kõik variandid prinditi kolmest materjalist, milleks olid ABS, PC ja PPA-CF. 3D prinditi kokku 27 katsekeha, mida katsetati Instron 5969 katsemasinaga osaliselt vastavalt EVS-EN ISO 178:2019 standardile. Katsetulemused näitasid, et suurim maksimaalne kandevõime oli PPA-CF materjalil, sellele järgnes PC ning kõige väiksem kandevõime oli ABS-il. Alumiiniumist tugevdusriba suurendas kandevõimet igas materjalis 10–16% ning I-tala ristlõige suurendas jäikust, kuid tõi kaasa purunemise väiksemate siirete korral. Suurimat jõudu massi kohta saavutas PPA-CF alumiiniumsulamist tugevdusribaga variant (10,2 N/g). Sitkuse seisukohalt oli parim PC, mille katsekehad taluvad koormust suurema läbipaindeni. Töö tulemused annavad praktilisi suuniseid 3D prinditavate droonikäppade tugevuse ja jäikuse suurendamiseks.
The aim of this bachelor’s thesis was to investigate ways to increase the strength and stiffness of a 3D printable FPV drone arm. During the project, three variants of the drone arm were designed: an original propeller with a rectangular cross-section, an I-beam-shaped drone arm, and an arm with an aluminum alloy reinforcement rib. All variants were printed using three materials: ABS, PC, and PPA-CF. A total of 27 test specimens were 3D printed and tested using an Instron 5969 testing machine, partially in accordance with the EVS-EN ISO 178:2019 standard. The test results showed that the highest maximum load-bearing capacity was achieved with the PPA-CF material, followed by PC, while ABS had the lowest load-bearing capacity. The aluminum reinforcement strip increased the load-bearing capacity of each material by 10–16%, and the I-beam cross-section increased stiffness but led to fracture at lower displacements. The highest strength-to-weight ratio was achieved by the PPA-CF variant with an aluminum alloy reinforcement strip (10.2 N/g). In terms of toughness, PC performed best, with test specimens withstanding loads until greater deflection. The results of this study provide practical guidelines for increasing the strength and stiffness of 3D printed drone arms.
The aim of this bachelor’s thesis was to investigate ways to increase the strength and stiffness of a 3D printable FPV drone arm. During the project, three variants of the drone arm were designed: an original propeller with a rectangular cross-section, an I-beam-shaped drone arm, and an arm with an aluminum alloy reinforcement rib. All variants were printed using three materials: ABS, PC, and PPA-CF. A total of 27 test specimens were 3D printed and tested using an Instron 5969 testing machine, partially in accordance with the EVS-EN ISO 178:2019 standard. The test results showed that the highest maximum load-bearing capacity was achieved with the PPA-CF material, followed by PC, while ABS had the lowest load-bearing capacity. The aluminum reinforcement strip increased the load-bearing capacity of each material by 10–16%, and the I-beam cross-section increased stiffness but led to fracture at lower displacements. The highest strength-to-weight ratio was achieved by the PPA-CF variant with an aluminum alloy reinforcement strip (10.2 N/g). In terms of toughness, PC performed best, with test specimens withstanding loads until greater deflection. The results of this study provide practical guidelines for increasing the strength and stiffness of 3D printed drone arms.
Kirjeldus
Bakalaureusetöö
Tehnika ja tehnoloogia õppekaval
Märksõnad
bakalaureusetööd, 3D printimine, FFF, droonikäpp, ABS, PC, PPA-CF
