2018, Vol. 16, No. 5

Selle kollektsiooni püsiv URIhttp://hdl.handle.net/10492/5378

Sirvi

Nüüd näidatakse 1 - 20 32

Air-conditioning in the cabins of passenger cars
(2018) Kumar, S.; Cerny, J.; Kic, P.
The objective of this paper is to analyse the current state of the constructional design and operational conditions of air - conditioning device in passenger cars. The research was focused on the function of air - conditioning equipment of passenger cars Skoda and KIA in various modes of operation during the winter, spring and summer season at different levels of air conditioning (without air - conditioning, minimum, medium and maximum level). Air temperature, air humidity, globe temperature, CO 2 concentration, dust concentration and noise inside the cabin w ere measured. Solar radiation plays a big role to rise up temperature inside the cabin. It resulted in the higher values of globe temperature than temperature of the air. The results of the measurements showed that CO 2 values were significantly lower than 2,500 ppm at minimum air - conditioning, lower than 600 ppm at medium and lower than 500 ppm at maximum level of air - conditioning. For all vehicles, dust concentration was greater when it measured with the air conditioning switched off than with the air con ditioning system turned on. The measurements confirmed that the total dust concentration was not more than 47 μg m - 3 , PM 10 lower than 28 μg m - 3 and PM 1 lower than 27 μg m - 3 . The noise levels ranged from 49.1 to 68.7 dB(A). The air - conditioning had very positive impact on the inside comfort in car cabins from all points of view during all periods of the year.
Analysis and forecast of performance characteristics of combine harvesters
(2018) Zubko, V.; Roubik, H.; Zamora, O.; Khvorost, T.
This article presents results of an experimental research of qualitative indicators of the modern combine harvesters (Case IH Axil Flow 8230, MasseyFergusonMFT7, JohnDeereS680i, ClaasLexion760, NewHolland CR9.80) used for winter wheat harvesting. Based on the results obtained, determination was made regarding the productivity of combine harvesters on the field, fuel consumption, and field conditions influence the grain loss and grain damage caused by a harvester. When conducting the experimental research of a combine's performance on the field a study of the effectiveness of the combine JohnDeereS680i was made on different modes. A program 'Machine Unit', designed by the authors, was used for the determination of productivity, fuel consumption and quality indicator for harvesting.
Analysis of gamma rays induced variability in lentil (Lens culinaris Medik.)
(2018) Tabti, D.; Laouar, M.; Rajendran, K.; Kumar, S.; Abdelguerfi, A.
In this study, a lentil variety, Idlib-3, was subjected to 100 Gy (LD50) gamma-ray irradiation. At M2, mutant families were characterized for the most beneficial agronomic traits. High genotypic coefficient of variation, broad sense heritability and genetic advance of the traits such as seed yield per plant and hundred-seed weight indicated expression of additive gene action and confirmed the response at early generation selection. Total number of pods per plant had positive correlation and the highest positive direct effect on seed yield per plant and hence the preference should be given for this trait during selection. The novel mutant families identified with early flowering, early maturity (families 5 and 90) in cluster I, and more first pod height (families 10,70 and 82) in cluster II could be utilized to breed short duration lentil varieties suitable for machine harvest.
The application of micro-wave treatment to reduce barley contamination
(2018) Kretova, Y.; Tsirulnichenko, L.; Naumemko, N.; Popova, N.; Kalinina, I.
The goal of this work is to study the applicability of ultra high frequency electromagnetic field treatment for decontaminating barley grain used in brewing while preserving its technological properties. The germination rates and/or yield of the treated sample seed were compared with those of the untreated seed germinated under normal conditions. To determine optimal treatment conditions, a two-factor analysis was carried out, taking the mycological state of the grain into account. The heating rate and the duration of electromagnetic exposure were chosen as variables; these values varied from 0.4 to 0.8 °C s-1 and from 30 to 90 s, respectively. It was found that germination of the treated barley seed was increased about 10.1–15.7% compared with that of the untreated seed. The microbial load decreased up to 80%. A heating rate of 0.4 °C s-1 and treatment exposure time of 30 s showed the strongest effect of decontamination while preserving the viability of the barley grain.
Can sustainability match quality citrus fruit growing production? An energy and economic balance of agricultural management models for ‘PGI Clementine of Calabria’
(2018) Di Vita, G.; Stillitan, T.; Falcone, G.; De Luca, A.I.; D’Amico, M.; Strano, A.; Gulisano, G.
This paper analyses energy and economic balances for different growing methods (conventional, integrated and organic cultivation) for Protected Geographical Indications (PGI) Clementine of Calabria, a quality-oriented citrus species in South Italy. Through a double methodological approach, the economic and energy sustainability of each production system was assessed by accounting for the farm net value (FNV) of farms. The energy employment in terms of direct (D) and indirect (I) sources and in terms of renewable (R) and non-renewable (NR) energy sources was also analysed. Regarding FNV, the results show that in the presence of European subsidies, organic farming (with 6.06 k€ ha-1) is more profitable than other systems (4.33 k€ ha-1 for integrated farming and 4.99 k€ ha-1 for conventional farming) due to the higher sales price of organic PGI clementines, which allow producers to obtain the highest remuneration for their capital (1.65 B/C organic, 1.48 B/C integrated, 1.61 B/C conventional). In addition, from an energy perspective, the organic farming systems showed better performances than conventional and integrated systems because they required the lowest average energy employment (49.5 GJ ha-1 year-1) compared with the integrated (57.2 GJ ha-1 year-1) and conventional scenarios (59.1 GJ ha-1 year-1).
The characteristics of wheat collection samples created by Triticum aestivum L/Triticum spelta L hybridisation
(2018) Diordiieva, I.; Riabovol, L.; Riabovol, I.; Serzhyk, O.; Novak, A.; Kotsiuba, S.
The aim of our research was to create, analyzes, and systematise wheat collection samples for the selection of valuable initial forms, to involve them in breeding process, and to create new productive cultivars. For this purpose the hybridisation of soft and spelt wheat was carried out, along with an evaluation of the hybrids that were obtained, between 2006 and 2018 (F5–F10). A collection of wheat samples, containing more than a thousand numbered items, was formed from the obtained diversity of samples. The economically-valuable and morphological characteristics of newly-developed materials were analysed. According to the results of our research, we selected forms of spelt, soft wheat, and speltoid samples which have high levels of productivity and high gluten and protein contents in grains. Spelt wheat sample 1817 contains 45.2% gluten, 22.3% protein, and has a yield capacity of 6.55 t ha-1 . Soft wheat sample 1689 has 32.4% gluten, 15.8% protein, and a yield capacity of 7.19 t ha-1 . These samples were submitted for state scientific and technical expert evaluation in 2018. The created varieties of European spelt wheat and Artemisia soft wheat were included in the ‘State Register of Plant Varieties Suitable for Distribution in Ukraine’. The varieties, Artaniia and Artaplot, were submitted for state scientific and technical expert evaluation.
A comparative analysis of functional traits in semi-natural grasslands under different grazing intensities
(2018) Targetti, S.; Messeri, A.; Argenti, G.; Staglianò, N.
The reduction of traditional management practices is a major threat for the conservation of permanent grasslands in many European marginal areas. The ecological importance of grasslands is acknowledged by the European Habitats Directive 92/43/EEC (1992) which includes many natural or semi-natural grassland types, and by the growing attention of society towards functions and services provided by these ecosystems. Nonetheless, the efficiency of conservation policies is questioned also for the lack of local-scale information on trends and state of grasslands hampers the definition of local-tailored schemes. The main objective of this work is to assess the potential of a set of functional traits in discriminating between different management intensities and their capacity to describe the dynamics occurring in semi-natural grasslands. The research was carried out in a hilly area of Tuscany (Italy) on four grassland sites characterized by similar environmental features (soil, climate, topography), and by different management practices for 10 or more years. The survey concerned collection and analysis of different functional traits related to foliar features, litter and botanical composition. The functional traits were able to differentiate the four sites under different management practices, but their effectiveness was different. Results support the possibility to perform a rapid appraisal of grassland successional stages based on leaf functional traits of dominant species and by the assessment of presence of a reduced number of species among those occurring in the community.
Comparative characteristics of antioxidant capacity of some forage plants of the Baltic Sea Region (a case study of the Kaliningrad Region and Estonia)
(2018) Chupakhina, G.N.; Shansky, Merrit; Parol, Argaadi; Chupakhina, N.Y.; Feduraev, P.V.; Skrypnik, L.N.; Maslennikov, P.V.
In this paper, we investigate changes in the antioxidant levels (anthocyanins, leucoanthocyanins, catechins) and the total water-soluble antioxidants capacity in forage plants in relation to their geography, i.e. proximity to northern or coastal areas. We demonstrate that the antioxidant content increases in unfavorable conditions, being higher in plants growing closer to the sea and in northernmost plants. Thus, since the total water-soluble antioxidants capacity is influenced by ecological factors, it may be used as one of the indicators in complex environmental assessment.
Determination of the tension limit forces of a barley malt and a malt crush in correlation with a load size
(2018) Hromasova, M.; Vagova, A.; Linda, M.; Vaculik, P.
This article deals with determination of selected parameters of barley malt (whole grain and crushed grain). The barley malt is besides water, hops and brewer's yeast, one of the basic ingredients necessary for the production of traditional Czech pilsner type of beer. The aim of this research is to determine limit force and internal friction angle with depending on the size of the load. The assessed malt crush was produced using a 2-roller malt mill. The 2-roller malt mill is based on the principle of grinding the material in a milling gap between two milling rollers, which is a very commonly used production of the malt crush. By determining the tension limits of the barley malt and the malt crush in correlation with the load, we can obtain very important parameters that inform us of the bulk material behavior, particularly with respect to the storage method (storage shape, height of the stored material layer, and the removal method from the storage, etc.), and to the transport (route gradient, transport speed, etc.). The determination of the tension limits has a direct link with cohesion of the bulk material and thereby contributes to establishing of the basic parameters of the bulk material, such as - the friction angle. The measurement for the angle of internal friction determination were performed on a prototype device. The principle of measurement on a mobile prototype devices is, the upper square chamber slides down the lower square chamber. Barley malt (whole grain and crushed grain) were loaded from 100 g to 5,000 g. The results of measuring were statistically analyzed with software Statistica 12.
The effect of herbicides on seed productivity of Festulolium
(2018) Obraztsov, V.; Shchedrina, D.; Kadyrov, S.
An artificially developed intergeneric hybrid Festulolium (+Festulolium F. Aschers, et Graebn.) is the best forage crop with high energy and protein nutrition value which can be used for green fodder when creating cultural haylands and pastures. The advantages of this crop are high regrow capacity, high content of sugars and good winter hardiness. Wide use of this new crop in fodder production is constrained, firstly, because the crop is yet new and little known and, secondly, because there is a lack of seeds due to imperfections in the production technology. There are still very few scientific studies on the biology and technology of Festulolium cultivation in the forest-steppe of the Central Chernozem Region of Russia. In our works we were the first to study the biological features of Festulolium and develop the main technological methods of growing and harvesting its seeds. The work was carried out in long-term studies of the Department of Crop Science, Forage Production and Agricultural Technologies of Voronezh State Agrarian University in 2009 2011. The soil in the experimental plot was leached medium loamy chernozem. The experiments involved the VIK-90 Festulolium variety with the preceding crop being the vetch-oat mixture harvested for green fodder. The soil preparation was conventional for seed herbage of perennial grasses in the Central Chernozem Region. The associated records and observations were made according to conventional methods adopted in the seed production of perennial grasses. A high efficiency of the Aurorex (0.55 L ha -1 ) and the Dicamba (0.15 L ha -1 ) herbicides in the suppression of annual and perennial dicotyledonous weed plants has been identified. The application of these herbicides has significantly reduced (by 40-73%) the weed infestation of seed herbage in the first year of vegetation and, as a result, has improved its structure and crop quality. The use of the developed agricultural techniques allows reducing the energy costs and receiving an average of 433 496 kg ha -1 of certified seeds.
Effect of nitrogen fertilization on sorghum for biomass production
(2018) Pannacci, E.; Bartolini, S.
Two field experiments were carried out in 2005 and 2006 in central Italy in order to evaluate the effects of different nitrogen (N) application rates (0, 50 100 and 150 kg ha-1 ) on flowering date, plant height, biomass production and partitioning (leaves, panicles and stems) and biomass quality of a sorghum hybrid (H133). Sorghum showed a high potential in terms of biomass production without N fertilization (18.5 t ha-1 of d.m. in 2005 and 26.6 t ha-1 of d.m. in 2006). The rate that maximized the biomass production was 100 kg ha-1 of N, increasing the biomass dry weight by 23.8% in 2005 and 18.8% in 2006, with respect to unfertilized sorghum; higher N rates are not advisable in order to avoid increasing fertilization costs and environmental impact without benefit of greater biomass production. The two highest N rates when combined with low water availability appeared to increase the rate of plant development, causing earlier flowering and increasing the percentage of panicles in total biomass. Higher heating value (HHV), lower heating value (LHV) and ash concentration of biomass varied among N rates, with values of HHV and LHV lower for unfertilized sorghum (17.6 and 16.7 MJ kg-1 d.m., respectively) than when N was applied (from 19.0 to 19.7 and from 18.1 to 18.8 MJ kg-1 d.m., respectively); on the contrary, ash concentration was greater for unfertilized sorghum (7.5% d.m.) than for fertilized sorghum (from 5.8 to 6.7% d.m.). This research showed the high potential of sorghum in terms of biomass production also when cultivated with limited irrigation and fertilization inputs. The biomass dry yield obtained by one hectare of sorghum crop without N nitrogen fertilization (i.e. 22.6 t ha-1 of d.m., average of 2005 and 2006 values) produces the same energy, by thermal utilisation, of 9.3 toe, that is equivalent to energy produced by 10,385 L of diesel fuel or 11,097 m3 of methane fuel. This aspect increases the certainty of the energetic and environmental sustainability of sorghum crop.
The effect of soil conditioner on the spatial variability of soil environment
(2018) Urbanovičová, O.; Krištof, K.; Findura, P.; Mráz, M.; Jobbágy, J.; Križan, M.
The aim of the study was to assess and evaluate the effect of soil conditioner on the spatial variability of soil environment. Activator PRP-SOL conditioning soil properties was selected as a field of study. Assessment of soil environment was done through the evaluation of selected soil properties, namely, tensile resistance of the soil and soil infiltration ability. Two dose of PRP-SOL application was done twice in year 2015 (Autumn and Spring) and once in 2016 (Spring) with application rates 150 kg ha-1 and 140 kg ha-1 , respectively. The area was divided into blocks where stimulators were applied and none treated as a control. The evaluation of recorded values showed that treatability and tillage itself was significantly better on the area which was treated by application of PRP-SOL activators. In addition, tensile resistance was decreased by 5.71% in comparison with non-treated area of experimental field. Since the infiltration ability is among the very important soil properties which have an effect on soil moisture regime as well as surface runoff and therefore soil erosion. The evaluation of recorded values has revealed the effect of treatment by PRP-SOL activators on soil infiltration ability and therefore it results in increases infiltration of precipitation as well. Overall increase of infiltration was recorded at value 2 mm h -1 . It can be concluded that application of soil activators may increase the soil conditions and therefore not only conserve soil fertility but even increase it from the long term perspective.
The effect of starter cultures on the qualitative indicators of dry fermented sausages made from poultry meat
(2018) Zinina, O.; Merenkova, S.; Soloveva, A.; Savostina, T.; Sayfulmulyukov, E.; Lykasova, I.; Mizhevikina, A.
Changes in physicochemical, rheological and microbiological properties occurring throughout the ripening (on days 0, 7, 14, 21, and 28) of dry fermented sausages made from poultry meat were studied. The effect of starter bacteria on the microstructure and sensory attributes of dry fermented sausages has also been determined. The results of physicochemical analysis of dry fermented sausage shows no significant difference (P < 0.05) between the test (inoculated) and the control sausages in the protein, fat, moisture, salt, ash and nitrite content. However, the significant difference (P > 0.05) between the control and inoculated batches in lowering the pH level, changing the critical shear stress, growth of viable microorganisms, accumulation of amine nitrogen during ripening was established. The results show, that inculcation of starter cultures accelerates biochemical processes during fermentation and thereby provides the necessary functional and technological properties of minced meat. Sensory profiling showed a more significant (P < 0.05) acidic and spicy flavour and intensity of acidic and smoked meat aroma; and increased firmness and cohesiveness in inoculated sausage. The results of microstructural analysis showed that the dry fermented sausages that ripened with the starter bacteria (Lactobacillus curvatus, Staphylococcus carnosus, Pediococcus pentosaceus), differ from the control sample compacted as a thin surface layer which is formed during the drying, smoking and maturation, and that indicates more uniform moisture removal.
Effects of Dormex (Hydrogen Cyanamide) on the performance of three seedless table grape cultivars grown under greenhouse or open - field conditions
(2018) El Masri, I.Y.; Rizkallah, Jad; Sassine, Y.N.
Greenhouse cultivation of table grapes is still limited to some experimental trials at Lebanese coast. One major constraint facing this type of cultivation is the lack of enough chilling hours causing irregular bud - break and yield reductions. Dormex, with Hydrogen Cyanamide as active ingredient, is an effective mean for dormancy release adopted in warm winter regions. The work investigated separate and combined effects of two factors: greenhouse cultivation and Dormex application on vine buds (following win ter pruning) on three - year old seedless cultivars (ARRA15, ARRA18, and ARRA19). Control consisted of non - treated plants grown in open - field. Results showed that Dormex application under greenhouse induced budburst uniformity, increased budburst percent (by 60%), number of flowers and fruits per shoot (by 83%) and vine productivity (by 90%) in all cultivars compared to control. Bud formation was increased under greenhouse and was reduced by Dormex treatment. Under greenhouse, elongation of current season sho ots was delayed and shoot length was reduced in treated plants, harvest was earlier by 7, 14, and 30 days in non - treated plants of ARRA18, ARRA19 and ARRA15 respectively and full fruit set (100%) occurred for all plants. Dry weight of shoots was improved b y Dormex application in both cultivation systems. All ARRA cultivars responded similarly to experimental factors except ARRA 19 under greenhouse where shoot length was enhanced in all plants while bud formation only in treated plants. Finally, treating vin e by Dormex under greenhouse was found as efficient tool to improve bud break and advance harvest under the specific Lebanese coastal conditions.
Environmental risk assessment studies on new plant protection products which have been elaborated from coniferous tree bark
(2018) Jankevica, L.; Polis, O.; Korica, A.; Samsone, I.; Laugale, V.; Daugavietis, M.
Nowadays there are still various chemical pesticides being applied in the course of ensuring plant protection. Since 2010, we have been working on the development of new, environmentally-friendly plant protection products which will provide an effective tool against pathogenic fungi and bacteria which cause disease in crop plants. The specific aim of this study was to evaluate a risk assessment for new plant protection products that have been elaborated on the basis of coniferous tree bark. Various products were tested which are extracted during the processing of wood bark from pine (Pinus sylvestris L.) and spruce (Picea abies (L.) Karst.). Ethanol extracts were formulated and applied during these experiments. Two formulations, which showed anti-fungal activity in vitro and in field trials on fruit crops (involving strawberries and raspberries) were selected for the risk assessment studies. The impact was studied of formulation treatment on crop plants and soil biological activity, and the accumulation of residues of active substances in crop plants and soil. The application of new formulations did not show any negative effect on the chlorophyll content and the chlorophyll fluorescence of plant leaves. The results showed that pine and spruce bark extract formulations contain active compounds (coumaric acid, quercetin, epicatechin, and ferulic acid) within the range of 5.1–5.9 mg kg-1 and 11.1– 443.9 mg kg-1 respectively. The amount of active substances which were determined in most cases was higher in the spruce bark extract formulation when compared to the pine bark extract formulation. Our results confirmed the presence of active compounds – epicatechin, quercetin, and coumaric acid – in strawberry fruits which remained untreated and in those that were treated with spruce ethanol extract formulation. Untreated raspberry fruits contained all four active substances within the range of 81–5,300 µg kg-1. We observed a significant increase of coumaric acid and quercetin in raspberries after their having been treated with spruce bark extract formulation in a 2% concentration, P < 0.05, and did not find any negative impact for spruce bark extract formulations when used on soil microbial biomass.
Evaluation of rice by-products, incubation time, and photoperiod for solid state mass multiplication of the biocontrol agents Beauveria bassiana and Metarhizium anisopliae
(2018) Bich, G.A.; Castrillo, M.L.; Villalba, L.L.; Zapata, P.D.
The success of biological control of insect pests depends not only on the isolation, characterization, and pathogenicity, but also on the success of the mass production of the microbial agents. The biological control strategy using entomopathogenic fungi like B. bassiana and M. anisopliae can only be useful if practical and economic methods of mass multiplication are available. Rice by-products like broken rice grains, rice hulls and their combination was evaluated for solid state multiplication of B. bassiana and M. anisopliae. The influence of photoperiod and incubation time in the production of conidia was also evaluated. This study showed that, broken rice was the most productive substrate for conidial production of both fungal genera, with a yield of 4.62 x 107 and 2.22 x 106 conidia g-1 respectively. Also, under the evaluated solid state multiplication conditions, the best conidia production was achieved with a photoperiod of 24 h of light for B. bassiana (with 4.43 x 107 conidia g-1) and M. anisopliae (with 1.35 x 106 conidia g-1). The results here demonstrated that these two fungal species could viably be multiplied with good yields of conidia on agro-industrial by-products using solid-state culture and regulating some culture conditions.
Experimental investigation of the work of a ploughing aggregate, operating according to the system ‘push- pull’
(2018) Bulgakov, V.; Ivanovs, S.; Arak, Margus; Kuvachоv, V.; Shymko, L.; Bandura, V.; Estonian University of Life Sciences. Institute of Technology
The use of ploughing machine - and - tractor aggregates, operating according to the principle of ‘push - pull’ , finds increasing application in the world since it allows ensuring the stability of the movement and the depth of ploughing, reduction of the energy indicators. The aim of this experimental study is to determine under field conditions the dynamic and ope rational technological parameters of the ploughing machine - and - tractor aggregate, operating according to the ‘push - pull’ system. This aggregate was an integral ploughing - tillage wheeled HTZ 16131 tractor, in front of which there was mounted a two - bottom pl ough, and at the rear – four - bottom ploughs. This aggregate has satisfactory path parameters of the movement during the execution of the technological process of ploughing. The oscillations of the furrow path for this aggregate are of a low - frequency natur e and are concentrated in a rather narrow frequency range (0...50 m - 1 ). At the operating speed of 2.0 m ∙ s - 1 it is 0...0.16 Hz. The maximum value of the mutual correlation function between the input impact (the turning angle of the driven wheels of the aggr egating tractor) and the output value – its relative bearing is positive and reaches a value of 0.88. Stability of the ploughing depth for the aggregate according to the ‘2 + 4’ scheme is ± 1.65 cm 2 , which is normally the smaller value of the same indicato r for a serial ploughing aggregate (± 1.98 cm 2 ).
Experimental study of an improved root crop cleaner from admixtures
(2018) Bulgakov, V.; Ivanovs, S.; Nowak, J.; Bandura, V.; Nesvidomin, A.; Ihnatiev, Ye.
One of the ways to raise the quality of sugar beet harvesting is the use of improved digging tools that are able to dig out root crops from the soil without any loss and considerable damage, as well as cleaners of the heap from admixtures. Perspective are the root crop harvesting machines, built according to the modular principle, where, depending on the state of the beet plantation, the composition of the cleaning tools, and the kinematic and technological modes of their operat ion are determined. To carry out experimental studies, experimental equipment was made which, under laboratory and field conditions, made it possible to obtain qualitative separation indicators of the heaps of sugar beet roots with wide variation in the ra nge of kinematic and design parameters of the improved cleaner. As the results of the laboratory and field experimental studies showed, in each of the two stages of cleaning the beet heap, a sufficiently high degree of removal of the soil admixtures and pl ant residues is ensured. Thus, at the first, preliminary stage of cleaning, the removal of admixtures amounted to 65.5 – 75.8%. After the second, basic stage of cleaning, the transported heap contained no more than 1.9% of admixtures. The results of the laboratory and field tests indicate that the proposed design of an improved sugar beet root cleaner from admixtures is prospective.
Fatty acid composition in pork fat: De-novo synthesis, fatty acid sources and influencing factors – a review
(2018) Vehovský, K.; Zadinová, K.; Stupka, R.; Čítek, J.; Lebedová, N.; Okrouhlá, M.; Šprysl, M.
Fats are among the basic nutrients the human organism needs as a source of energy, as well as to grow and regenerate cells, tissues, and organs. Particularly animal fats, with their higher proportion of saturated fatty acids and low content of n-3 fatty acids, are often seen by the public as relatively undesirable food components. Fatty acid (FA) composition of pork is affected by many factors: genotype, breeding, gender and feeding methods. Numerous research teams, therefore, have searched for means of effectively manipulating the chemical composition of animal fats. This paper reviews existing knowledge and means of effectively influencing the fatty acid composition in pig fat, which is a significant component of human food in European countries due to their high consumption of pork. The findings of various authors demonstrate that not only altering of fatty acids sources in animal diets but a range of other factors as well can significantly influence the composition of fatty acids in pig fat and consequently pork quality.
Film agents as an effective means of reducing seed shattering in Festulolium
(2018) Obraztsov, V.; Shchedrina, D.; Kadyrov, S.
In the conditions of the forest steppe of the Central Chernozem region, methods were studied to reduce shatter losses in the pre-harvesting period for Festulolium during the period 2009–2011, applying the film forming agents, Elastik (0.8–1.2 L ha-1), Bifaktor (0.8–1.2 L ha-1), and Metylan Universal Premium (1.4–3.8 kg ha-1). The agents were used at seed humidity levels of between 60–65%. Following anti-shattering treatment, seed moisture content gradually decreased. The application of film forming agents prevented seed shattering, and seeds were harvested by direct combining at a humidity of between 20–25% without heavy losses being suffered. Moreover, decreased seed losses due to film forming agents significantly reduced the cost of seed heap drying. In the control treatment, the seed yield amounted to 214.8 kg ha-1, and 360.7 kg ha-1 was lost as a result of natural seed shattering in the process of ripening. The Elastik and Bifaktor preparations prevented seed shattering and contributed to the preservation of a seed yield of between 522.1–563.5 kg ha-1. The application of film forming agents contributed to a reduction in losses during harvesting within the range of 9.7–16.8%. Application of the Metylan Universal Premium glue in the studied doses provided a significant increase of seed yield. The highest seed yield (490.1–495.2 kg ha-1) was obtained in the treatment which used a Metylan application at a dose of 3.0–3.4 kg ha-1, where seed shattering was reduced by 14.8–17.6%.

Sirvi

Sirvi 2018, Vol. 16, No. 5 Pealkiri järgi

Tulemused lehekülje kohta

Sorteerimisvalikud