2017

Selle valdkonna püsiv URIhttp://hdl.handle.net/10492/5357

Sirvi

Nüüd näidatakse 1 - 20 72

The advantage of Decision Support System for managing spring barley disease in Estonia
(2017) Sooväli, Pille; Koppel, Mati; Lauringson, Enn; Talgre, Liina
A Decision Support System (DSS) I - Taimekaitse focusing on use of timely applied and reduced fungicide rates in control of cereal diseases has been tested in field trials since 2003 . We compared the conventional treatment and the DSS - based spray practices in 18 field trials in five agricultural locations over 7 - year period. Efficacy of the control of net blotch caused by Pyrenophora teres (Drechsler, am Drechlera teres Sacc. Shoem), the main fungal disease in spring barley has been tested to determine the economic advantage of DSS use. Compared with the conventional spray practices, the advantage I - Taimekaitse resulted in reduction of application doses by 30 to 60% of the registered rate. According to I - Taimekaitse , the fungicides were applied mainly between heading and flowering growth stages (GS 55 – 65), whereas traditional routine spraying is commonly made at booting (GS 37 – 49) . The experiment clarifies the cost - benefit of using DSS - based approach in barley disease management with average yield increase above the control in 12.8% and above the conventional treatment in 14.1%. I - Taimekaitse gave competitive disease control and average yield output reduction compared with conventional practice by 9%. In general the Treatment Frequency Index applied in conventional treatment was 0.65 and in DSS 0.41. Although the cost of treatment expense in DSS was 20% less compared with conv entional practice, the performance of conventional used spray practices was outstanding in economic return.
AFLP-analysis of genetic diversity in soybean [Glycine max (l.) Merr.] cultivars Russian and foreign selection
(2017) Zargar, M.; Romanova, E.; Trifonova, A.; Shmelkova, E.; Kezimana, P.
Genetic diversity of 11 cultivars of soybean (Glycine max) from a VIR (N.I. Vavilov Institute of Plant Genetic Resources) collection was analyzed by the AFLP (amplified fragment length polymorphism) technique. From 18 tested primer combinations, both of them were selected for further analysis. From these two primer combinations (E32/M60 and E32/M59), 90 DNA fragments were obtained, 39 (43%) of them were polymorphic. Unique DNA fragments were found in accessions SibNIISHoz 6, Soer-4, Determinant. The Jaccard's similarity indices varied from 0.79 (between Sonata and Ugra) to 0.94 (between Ugra and Garmoniya) with an average of 0.775. Cluster analysis placed the cultivars into the several groups but separation in groups was not related to their origin or biological characteristics, even though cultivars Nordik and Soer-4 (cultivars recommended for Central Black Earth region of Russia) clustered together on the dendrogram. The obtained high values of Jaccard genetic similarity index and low level of polymorphism and differentiation illustrated a relatively low genetic diversity in our studied cultivars, which correlated with different other studies on soybean genetic diversity with AFLP-analysis.
Anaerobic co-digestion of oil refinery wastewater and chicken manure to produce biogas, and kinetic parameters determination in batch reactors
(2017) Mehryar, E.; Ding, W.M.; Hemmat, A.; Hassan, M.; Bi, J.H.; Huang, H.Y.; Kafashan, J.
In order to improve the anaerobic fermentation of oil refinery wastewater (ORWW) via an appropriate nutrients pool for microbial and buffer capacity growth, a study was carried out on related anaerobic co-digestion (AcoD) with a rich organic carbon source, namely chicken manure (CM). The kinetic parameters were investigated (including cumulative biogas production, bio-methane content, retention time, and soluble chemical oxygen demand stabilisation rate) of batch AcoD experiments related to six ORWW:CM-ratio treatments (5:0, 4:1, 3:2, 2:3, 1:4, and 0:5) under mesophilic conditions. The highest soluble chemical oxygen demand removal rate was obtained for the 4:1-ratio treatment. However, the highest biogas production and bio-methane contents were achieved for the 1:4-ratio treatment. When taking into consideration the highest oil refinery wastewater portion in the AcoD mixtures and the statistical test results (LSD0.05) for the kinetic parameters, it can be seen that the 4:1-ratio treatment provided the maximum biogas production levels.
Analysis of Arabidopsis defensin-like genes and ovule development during fertilization and Fusarium infection
(2017) Spalvins, K.; Blumberga, D.
Defensins are small, highly stable antimicrobial peptides. Many defensin-like (DEFL) peptides found in flowering plant Arabidopsis thaliana are believed to have role in either natural immunity or cell-to-cell communication during fertilization. However, little is known about the DEFL peptides and their functions during these events. The goal of this work is to investigate the genes encoding selected DEFLs by observing their expression patterns during fertilization and Fusarium graminearum infection. According to the results 4 selected genes of interest (GOI) are downregulated after fertilization and infection and mock treatments are causing degradation and delay of development in treated ovules.
Assessment of different growing conditions for enhanced postharvest quality and shelf-life of leaf lettuce (Lactuca sativaL.)
(2017) Lee, J.-S.; Nath, U.K.; Goswami, G.; Nou, I.S.
Lettuce is the most important leafy vegetable. It is exclusively used as freshly raw form but sometime also as cooked. However, its quality depends on several pre- and postharvest factors. The effects of growing conditions and cultivars on the postharvest quality of leaf lettuce were investigated. In this experiment the interaction of variable factor; like growing conditions and fixed factor; cultivars are also observed. The leaf lettuce cultivars ‘Cheongchima’, ‘Cheongchuckmyeon’, ‘Geockchima’ and ‘Geockchuckmyeon’ were grown under favourable (natural condition) and unfavorable growing condition (with excess soil water and 50% shading) to evaluate their shelf-life and postharvest qualities. Plant height and the number of leaves were significantly varied in different growing conditions and by cultivars. In addition, fresh weight was affected by only growing condition, whereas leaf thickness was influenced by cultivars, growing conditions and the cultivars influenced the degree of fresh weight loss and respiration rate during postharvest storage. However, the postharvest storage qualities differed with cultivars and in combination with growing conditions.Leaf thickness and quality of leaf lettuce before and after harvest were also varied by cultivars and growing conditions. It could be concluded that postharvest leaf lettuce quality remains acceptable when growing under excess soil water with 50% shading.
The assessment of hazelnut mechanical harvesting productivity
(2017) Bernardi, B.; Tous, J.; Benalia, S.; Abenavoli, L.M.; Zimbalatti, G.; Stillitano, T.; De Luca, A.I.
Hazelnut cultivation represents a new opportunity for Calabrian mountainous and sloping areas (Southern Italy), where no alternative fruit crops, except forestry, could be settled. In this Region, hazelnut production doubled during the last fifty years, inciting the farmers to introduce mechanization in cropping practices such as harvesting in order to increase productivity and decrease production costs. Indeed, harvesting is currently one of the most expensive processes of the productive cycle, moreover to be time consuming if carried out manually. Mechanization degree depends significantly on the terrain topography: in sloping areas, rakes are often associated to aspirating machines to harvest the fallen fruit, while the employment of harvesting machines from the ground prevails in flat areas. In this context, the present paper aims to assess technical and economic aspects of harvesting operation, using a harvester from the ground model ‘Jolly 2800’ (GF s.r.l., Italy). Particularly, for technical purposes data about operational working time as well as working productivity were collected according to CIOSTA requirements, in two harvesting sites, whereas, for mechanical harvesting economic evaluation, an estimation model was applied to calculate machinery cost per hour. Moreover, the cost per kg of hazelnut in shell and the average cost per hectare were estimated also. The obtained results show a working productivity of 0.065 ha h-1 op-1 in the first harvesting site, while it was equal to 0.022 ha h -1 op-1 in the second one. Concerning the average cost per hectare, the second harvesting site showed the worst economic performances, with 550.76 € ha-1 against 182.54 € ha-1 obtained in the first one.
Band structures for binding and holding of objects made from recycled metallic materials
(2017) Mironovs, V.; Boiko, I.; Lisicins, M.; Zemcenkovs, V.
The aim of the present research is the investigation of the possibility and effectiveness of using the band structures made from recycled metallic materials for binding and holding of objects (in particular, tubular objects as pipelines or shells). The using of band elements and structures as such is a perspective way to increase the safety and bearing capacity of the pipelines and vessels. Nowadays during repair works the outer surfaces of the mentioned objects are braided by the steel tapes, i.e. the objects are strengthened by the binding. The mentioned steel bands are specially produced for binding purpose. From the other hand after stamping of smallsize details (like the elements of supply chains for different apparatus) the metallic waste in the shape of perforated metallic tapes are received and needs to be reused in compliance with the good practice in effective resource using and recycling. The band structures for binding and holding of tubular objects, produced from the perforated metallic tape by the longitudinal profiling, multilayer and spiral winding are presented. It is proposed to apply in industry the composite band structures made from perforated metallic materials and epoxy matrix for binding and holding of tubular objects as pipelines or shells, which allows simplifying and speeding up the repair works especially in the cases of the local damages.
Carbon content of below–ground biomass of young Scots pines in Latvia
(2017) Jansons, Ā.; Bārdulis, A.; Ķēniņa, L.; Lazdiņa, D.; Džeriņš, E.; Kāpostiņš, R.
Forest ecosystems play crucial role in global carbon cycling, therefore, increasing afforestation of agricultural land in Europe has been recognized as important contribution of carbon sequestration. In carbon reporting systems, root carbon content (CC) default value has been set to 50%. The study aimed to estimate CC in below–ground biomass and in relation to tree age in young Scots pine stands on forest and former agricultural land. The below–ground CC of young (8 to 40 years) managed Scots pine (Pinus sylvestris L.) stands growing on nutrient poor mineral soils in Latvia was carried out. In total 62 sample trees (43 in forest land, 19 in former agricultural land) were randomly selected for destructive sampling to estimate the CC within below–ground biomass. Below–ground biomass weighted mean CC was 49.7 ± 0.4%, being slightly lower than the default CC value used to calculate carbon budgets. Root fractions stump, small roots (diameter 2–20 mm), coarse roots (diameter > 20 mm)) differed (p < 0.001) in their CC. Stumps (50.6 ± 0.6%) had highest (p < 0.001) CC in the below–ground biomass, followed by coarse (49.5 ± 0.4%) and small (49.1 ± 0.4%) roots, which did not differ from each other in their CC. Results demonstrated age–dependent increase of CC (p < 0.001) from 48.2 ± 0.3% to 51.7 ± 0.5%, indicating overestimation of the default value during the first two decades, but underestimation for older trees (24 to 40 years).
Chemical composition of seeds and green beans of common bean varieties, breeded in Omsk State Agrarian University under conditions of southern forest-steppe zone of Western Siberia
(2017) Kazydub, N.; Pinkal, A.; Marakayeva, Т.; Kuzmina, S.; Korobeinikova, M.; Kotsyubinskaya, O.
The article considers the biochemical composition of green beans and seeds of common beans varieties, breeded in Omsk State Agrarian University named after P.A. Stolypin (OmSAU). The research was conducted in 2014–2016. Varieties of locally breeded beans, in comparison with the standards, have advantages in the content of protein, zinc, iodine, calcium, iron, sugar; green bean technological properties and tenderizing of seeds during cooking, which becomes an indispensable component of the diet.
Comparison of mechanical and electric drive of mulcher
(2017) Pexa, M.; Čedík, J.; Kumhála, F.; Pražan, R.
The contribution is focused on comparison of mechanical and electric drive of mulcher with vertical axis of rotation by means of mathematical model. The mulcher has working width of 6 m and it is usually aggregated with tractor of minimal power of 150 kW. On the test plot the torque and power transferred trough the tractor PTO, fuel consumption and the production of gaseous emissions components were monitored. This field measurement served as a basis for modelling as well as measured complete characteristics of the combustion engine of the tractor John Deere 7930. As a main base for the modelling the record of real operation of the tractor with mulcher was used. Then, in the software product MathCad the operation of the tractor with mechanical and electrical drive of the mulcher was modelled. In the case of the electrical drive of the mulcher the tractor with internal combustion engine, connected to generator was taken into consideration. Due to overall lower efficiency of the electrical drive with generator, worse values of the fuel consumption and emissions production in comparison with mechanical drive were reached in case of electric drive. At hypothetical use of batteries (100% electro-powered tractor) and when the energy mix at Czech Republic is taken into consideration, it is possible to reach the quarter values of emissions production in comparison with combustion engine.
Comparison of selected remote sensing sensors for crop yield variability estimation
(2017) Křížová, K.; Kumhálová, J.
Currently, spectral indices are very common tool how to describe various characteristics of vegetation. In fact, these are mathematical operations which are calculated using specific bands of electromagnetic spectrum. Nevertheless, remote sensing sensors can differ due to the variations in bandwidth of the particular spectral channels. Therefore, the main aim of this study is to compare selected sensors in terms of their capability to predict crop yield by NDVI utilization. The experiment was performed at two locations (Prague-Ruzyně and Vendolí) in the year 2015 for both locations and in 2007 for Prague-Ruzyně only, when winter barley or spring barley grew on the plots. The cloud-free satellite images were chosen and normalised difference vegetation indices (NDVI) were calculated for each image. Landsat satellite images with moderate spatial resolution (30 m per pixel) were chosen during the crop growth for selected years. The other data sources were commercial satellite images with very high spatial resolution – QuickBird (QB) (0.6 m per pixel) in 2007 and WorldView-2 (WV-2) (2 m per pixel) in 2015 for Prague-Ruzyně location; and SPOT-7 (6 m per pixel) satellite image in 2015 for Vendolí location. GreenSeeker handheld crop sensor (GS) was used for collecting NDVI data for both locations in 2015 only. NDVI calculated at each of images was compared with the yield data. The data sources were compared with each other at the same term of crop growth stage. The results showed that correlation between GS and yield was relatively weak at Ruzyně. Conversely, significant relation was found at Vendolí location. The satellite images showed stronger relation with yield than GS. Landsat satellite images had higher values of correlation coefficient (in 30 m spatial resolution) at Ruzyně in both selected years. However, at Vendolí location, SPOT-7 satellite image has significantly better results compared to Landsat image. It is necessary to do more research to define which sensor measurements are most useful for selected applications in agriculture management.
Comparison of tillage systems in terms of water infiltration into the soil during the autumn season
(2017) Kovář, S.; Mašek, J.; Novák, P.
The soil belongs to the most valuable parts of the planet Earth. It is, endangered by water erosion, which causes huge destruction every year, or damage to farmland. More than half of the agricultural land in the Czech Republic is threatened by water erosion. The measurement was performed in the location Nesperská Lhota. The trial has been established on loamy sand Cambisol. In the field experiment, there were created 6 different variants which wad differed by soil tillage and crop. In the individual variants maize and oats were located. The field trial has been existing for a long time, as it was founded in 2009. Two measuring methods of water infiltration were used for the measurements: a mini disk infiltrometer and a single ring. The measurement was performed in the period of September 2016 before the harvest of maize. The soil aggregates were already stabilized at that time after all tillage operations. The measurement result showed the difference between the methods of soil tillage. The greatest ability of infiltration had a variant of maize with inter-row oats. Surprisingly, it was followed by maize, which was processed by ploughing technology. The lowest infiltration capacity was showed by oats reduced by soil tillage. A variant without vegetation had the second lowest infiltration. Our results obtained at rate of water infiltration into the soil affirm the need to control measures in the late vegetative stages. It is important for most of the rainfall to be quickly infiltrated so that it prevents the formation of massive surface runoff.
Comparison of tractor slip at three different driving wheels on grass
(2017) Abrahám, R.; Majdan, R.; Drlička, R.
The paper deals with a possibility of tractor slip reduction on a grass and evaluates an use of two versions of special wheels. Both prototypes were developed at the Department of Transport and Handling of the Slovak University of Agriculture in Nitra. The first system was designed in 2010 year as blades wheels. The second system (spikes device) consists of spikes which are mounted onto standard tractor tyres with special cuts, was designed in 2014 year. The spikes are settled in these cuts while moving on road surface. The second one is placed near the drive wheels and uses the blades. The spikes and blades are ejected to reduce wheels slip when tractor operates on grass or soil. The base position allows tractor transport on road with standard tyres. The goal of experiments realized on grass surface was to compare mutually slip behaviour achieved. The measurements were realized with standard tyres without any modification, too. A tractor with three types of drive wheels were loaded by heavier tractor. Drawbar pull and wheel rotation speed for slip calculation were measured in tests. The results show a fact that a loss of energy due to the wheels slip increases, while a penetrometric resistance in the surface layers of a soil decreases, at soil humidity 33.2%. An application of both prototypes is very advantageous because they reduce the wheels slip, increase tractor operation efficiency and so protect the soil.
The content of weed seeds in the soil based on the management system
(2017) Kuht, Jaan; Eremeev, Viacheslav; Talgre, Liina; Madsen, Helena; Toom, Merili; Mäeorg, Erkki; Loit, Evelin; Luik, Anne; Estonian University of Life Sciences
In 2008 an experiment was set up on the field in Eerika experimental station (Estonian University of Life Sciences) as a 5-field crop rotation: barley (Hordeum vulgare L.) with undersown red clover, red clover (Trifolium pratense L.), winter wheat (Triticum aestivum L.), pea (Pisum sativum L.), potato (Solanum tuberosum L.). The objective of the study was to measure the content of weed seeds in the soil and to evaluate the diversity of the species at the beginning of the period of organic production in 2011. In conventional farming systems without fertilizer (Con I) and conventional farming with mineral fertilizer (Con II) herbicides were used for weed control. All the crops in Con II system received P 25 kg ha-1 and K 95 kg ha-1 , but the application rates of mineral nitrogen fertilizer differed. In organic systems (Org I – organic farming based on winter cover crop and Org II – organic farming based on winter cover crop and manure), the winter cover crops (ryegrass after winter wheat, winter oilseed rape after pea, winter rye after potato) were sown after the harvest and were ploughed into the soil as green manure in spring. Organic farming systems (Org II) had a negative effect on the content of weed seeds in the soil (2.0–22.7% less seeds than in other variants). The seeds of Chenopodium album were the most abundant among summer annual weeds and the seeds of Viola arvensis among winter weeds in the soil. Organic farming measures increased the domination of Chenopodium album – the dominance index D’ was increased by 0.09–0.14 compared to conventional variants. The content of seeds of winter weed Viola arvensis in Org II variant was decreased by 82%. The index of species evenness J’ and Shannon Wiener diversity index H’ were lower in organic plots by 0.10– 0.18 and 0.60–0.19, respectively. Org II variants showed the best results based on the decrease of soil weed seed bank and distribution of the weed species.
Contribution of pumped hydro energy storage for more RES utilization on autonomous power systems
(2017) Katsiagiannis, Y.; Annuk, Andres; Karapidakis, E.S.; Estonian University of Life Sciences. Institute of Technology. Department of Energy Engineering
This paper addresses the performance issues of autonomous power systems under high renewable energy sources (RES) penetration. Renewable energy sources could be the main option for isolated power generation at remote locations in case that energy storage introduced. At the moment, pumped hydro storage (PHS) units and batteries storage systems (BSS) represent the most mature technologies for large scale energy storage. The basic criteria for this kind of energy storage unit installations include, (a) the existence of an autonomous power system with local power stations, (b) the high electricity production cost, (c) the potential of renewable energy sources (mainly wind and solar), and (d) the non-flat terrain morphology (for PHS). Greek islands represent ideal cases for large scale energy storage installations, as they fulfil all the above criteria. This paper shows the effect of the installation of a planned PHS unit in Crete island. The calculations are based on real data provided by the Cretan power system operator, whereas the results show the effect of energy storage units operation on the energy mix, as well as the economic viability of the project, which is combined with significant environmental benefits.
Critical velocity of solid mineral fertilizers in a vertical upward airstream and repose angle
(2017) Hůla, J.; Kroulík, M.; Honzík, I.
Critical velocity of mineral fertilizers in airstream is important not only at the application of fertilizers by spreaders but also at combine of fertilizing and sowing. The knowledge of angles of repose is important to design hoppers on spreaders for solid mineral fertilizers. Critical velocities for six solid mineral fertilizers were measured in the vertical aspiration duct of a laboratory sorting machine. Variation curves were constructed for particular fertilizers and the mean critical velocity of fertilizers (velocity of uplift) was computed. The mean critical velocity of fertilizers was between 8.53 and 12.43 m s -1 . The lowest critical velocity was found out in the fertilizer UREA 46%, the highest in the fertilizer LAV. Statistical significance of differences in the critical velocity of fertilizers was assessed. Angles of repose of eight solid mineral fertilizers were also measured and statistical significance of differences was evaluated. The highest values of repose angle were determined for potassium salt and ammonium sulfate (35.9° respectively 34.9°), the lowest values for UREA and LAV (28.7° respectively 29.6°). The obtained results extend information applicable to an assessment of parameters of the operation quality of spreaders during mineral fertilizer application.
Determination of mechanical properties of poppy waste pellets
(2017) Kažimírová, V.; Kubík, Ľ; Chrastina, J.; Giertl, T.
The work deals with evaluation of mechanical properties three types of pellet samples produced fro m poppy waste. The pellets were submitted to compressive loading. The compressive loading curves of dependencies of force on strain and force on time were realised. Certain mechanical parameters were determined, namely the diameter of the sample, length of the sample, force at 10% of strain, force in the first maximum of the force – strain curve, strain in the first maximum of the force – strain curve, modulus of elasticity, force in the inflex point of the force – time and force – strain curves and strain and stress in the inflex point of the force – time and force – strain curves. The work lists correlations of mechanical parameters of individual pellet types. The pellet type 1 made only of ground poppy head mass has shown the best results, the pellet type 3 consisting of ground poppy heads after harvest and waste from sieving of poppy seeds in mass proportion 1 : 1 has shown the worst results.
Dimethyl ether as a renewable fuel for diesel engines
(2017) Zeman, P.; Hönig, V.; Procházka, P.; Mařík, J.
The area of automotive fuel, or fuel components, which can be produced from biomass also includes dimethyl ether, otherwise known as DME. The issue of the use of DME as a fuel is one which has been monitored until recently. Biomass can also be used as the raw material for the production of DME. DME has therefore replaced the previously-used CFCs (chlorofluorocarbons), which are now banned for their role in dangerous levels of ozone depletion. With regard to its physical properties and combustion characteristics, it is currently expected that DME will soon apply significantly as a fuel in the municipal sector and in households, and as an alternative fuel for motor vehicles with diesel engines. DME is a suitable fuel for diesel engines and can be considered as one of the most promising diesel fuel replacements. DME is a suitable fuel for diesel engines mainly due to its low self-ignition temperature and good cetane figures. It is well miscible with most organic solvents and because the polar solvent is water-immiscible. The advantage is its high levels of purity, and its being free of sulphur, nitrogen, or metals. The physical properties of DME are very similar to the physical properties of LPG. DME requires relatively complex and costly fuel accessories, but the original compression ratio of the diesel engine is maintained. A diagram of the fuel system is illustrated in the paper. The paper analyses the dependence of vapour pressure on temperature, the dependence of the density on temperature, kinematic viscosity, the flash point, the boiling point, and the solubility of water. The objective is to evaluate this interesting energy source for applications in diesel engines.
Dry matter accumulation and nitrogen concentration in forage and grain maize in dryland areas under different soil amendments
(2017) Lamptey, S.; Yeboah, S.; Li, L.; Zhang, R.
Soil amendment plays significant role in improving soil fertility and increasing crop productivity in rain–fed agriculture. Understanding the grain yield associated with dry matter and N concentration is essential for improving maize production. A 3– year field study was conducted to determine dry matter accumulation, nitrogen concentration and grain yield of forage and grain maize under different soil amendments in the Western Loess Plateau of China. The experiment was conducted using a randomized complete block design with four treatments and three replicates per treatment. Results showed that dry matter accumulation and nitrogen concentration in the swine manure in combination with chemical fertilized (SC) crops was significantly higher (by ≈ 60% and 39%) than no amendment (NA) which therefore translated into increased grain yield ≈ 74%. The SC treatment also improved leaf area index and chlorophyll content (P < 0.05) by approximately 34% to 32% compared to NA, which supported the above results. The nitrogen concentration in the leaf was higher at jointing and lower at maturity. Grain yield positively correlated with dry matter accumulation and nitrogen concentration at jointing, flowering and milk stage. Dry matter accumulation and grain yield also increased in the sole swine manure (SM) and maize stover (MS) treatments, but to lesser extent than SC. Based on the improvement of dry matter accumulation, nitrogen concentration and grain yield, swine manure in combination with chemical fertilizer appears to be a better fertilization option under dryland cropping systems.
The effect of bedding amount on gas emissions from manure during storage
(2017) Šimon, J.; Vegricht, J.; Bradna, J.
One of the major agricultural pollutants of environment is manure from livestock. We focused on dairy cows kept in the barns with straw bedding commonly used in the Czech Republic. We tested the hypothesis that the amount of bedding used daily relative to the number and size of animals kept has a significant effect on the emissions of gases from manure stored in a manure pile. In the experiment, a group of 10 dairy cows of Holstein and Czech Red Pied breed was housed in a stable bedded with various amounts of wheat straw (4–10 kg/livestock unit per day). The manure was removed from the stable after 48 h and mixed was stored in cubic containers with drain floor allowing measurement of manure leachate release. For 50 days we measured weight, volume, weight of manure leachate and manure temperature. Decreasing stored manure weight can be attributed to release of manure leachate and emissions of gases, primarily water vapor, as a result of microbial activity and increased temperature in the manure during storage. Using the calculated model, we found that daily production of emissions of water vapor and other gases was related to bedding amount in a statistically significant manner (P < 0.001). The cumulative amount of gas emissions grew rapidly in all treatments. Also total amount of emissions was related to bedding amount in a statistically significant manner (P = 0.004). We also found the relationship between internal manure temperature and the logarithm of the amount of emissions produced to be statistically significant (P < 0.001).

Sirvi

Sirvi 2017 Pealkiri järgi

Tulemused lehekülje kohta

Sorteerimisvalikud