Sirvi Autor "Help, R." järgi
Nüüd näidatakse 1 - 4 4
Tulemused lehekülje kohta
Sorteerimisvalikud
Kirje Behavior of B20 fuels in arctic conditions(2019) Sirviö, K.; Niemi, S.; Help, R.; Heikkilä, S.; Hiltunen, E.Several renewable and sustainable liquid fuel alternatives are needed for different compression-ignition (CI) engine applications to reduce greenhouse gas (GHG) emissions and to ensure proper primary energy sources for the engines. One of the shortcomings of several bio oils and first generation biodiesels has been their cold properties. Still, the need for alternative fuels is also present in arctic areas where the storing of the fuels may become problematic. The main aim of the current study was to determine how the storage related properties of fuel blends change if the fuels first freeze and then melt again. The samples were analyzed three times: as fresh, and after the first and second freezing-melting phase transitions. The share of renewables within the blends was 20 vol-%. Rapeseed methyl ester (RME) and animal-fat based methyl ester (AFME) were blended with LFO in a ratio of 80 vol-% of LFO and 20-vol% of RME or AFME. The investigated and compared properties were the FAME content of the neat FAMEs, and kinematic viscosity, density, oxidation stability index, and acid number of the blends. Cold filter plugging point was measured for AFME and its blend. According to the results, the quality of the FAMEs and their blends did not change significantly during the freezing over. The freezingmelting phase transition seems, thus, not to be as big a threat to the fuel quality as the high temperatures are. According to the results of this study, the studied fuels were feasible after the freezing-melting phase transition.Kirje Effects of storage on the properties of rapeseed oil and alcohol blends(2021) Nuortila, C.; Heikkilä, S.; Help, R.; Suopanki, H.; Sirviö, K.; Niemi, S.Kinematic viscosity and density are important fuel properties because they influence fuel atomisation during injection into the engine cylinder. The viscosity and density of neat vegetable oils usually are too high to allow optimal use of these oils in compression ignition engines. Blending vegetable oils with alcohols can improve these properties, but it is not known whether the blend properties remain stable during storage. This study measured kinematic viscosity (at 40 °C), density (at 15 °C) and surface tension of rapeseed oil-alcohol blends that had been stored in closed borosilicate glass bottles at room temperature in the dark for 49 weeks. The values were compared with those of the fresh blends. Further measurements of oxidation stability for the rapeseed oil and the blends were taken after 72 weeks of storage. The blends consisted of rapeseed oil with ethanol at 5 vol–%, and rapeseed oil with 1–butanol at 5 vol–%, 10 vol–%, 20 vol–% and 30 vol–%. All in all, the observed changes during storage were small. Density values deviated by less than 1%, surface tension by no more than 3% and kinematic viscosity differed from the fresh blends’ values by 1% to 8%. Surface tension had increased in some blends and decreased in others. Kinematic viscosity rose in all blends, with the smallest increase measured for the rapeseed oil–butanol 30 vol–% blend. This blend also showed the best oxidation stability, which was close to six hours.Kirje Kinematic viscosity studies for medium-speed CI engine fuel blends(2018) Sirviö, K.; Niemi, S.; Help, R.; Heikkilä, S.; Hiltunen, E.Engine - driven power plants, run by diesel fuel or gas, will be needed for peaking power to keep the electricity grids stable when the production of renewable electricity, e.g. utilizing wind or solar power, is increased. The choice of the alternative, renewable fuels for engine - driven power plants and marine applications is at the moment quite narrow. The amount of renewables of all liquid fuels is at present less than 2%. Biodiesels, FAMEs, have been studied for long time and apparently, despite of the problems they may have, they are still in the great interest. One import ant increment to the category of alternatives is fuels that are produced from e.g. oil wastes, i.e., recycled fuels. They are not renewable, but recycling of potential energy raw materials is still one step forward in increasing the suitable and more susta inable options. To utilize the blends in medium - speed engines for power production, accurate knowledge of the physical and chemical properties of fuel blends is very important for the optimization of engine performance. The determination of the fuel kinema tic viscosity is needed to create proper fuel atomization. The injection viscosity affects directly the combustion efficiency and the engine power. Consequently, this study focused on measuring kinematic viscosity curves for seven fuel blends, as well as t he neat fuels used for blending. The temperature range was 10 – 90 °C. The fuels used for blending were rapeseed methyl ester, animal - fat based methyl ester, hydro - treated vegetable oil, light fuel oil and marine gas oil produced from recycled lubricating oi ls.Kirje Properties of local produced animal-fat based biodiesel and its blend with fossil fuel(2018) Sirviö, K.; Heikkilä, S.; Help, R.; Niemi, S.; Hiltunen, E.In the near future, more emphasis must be put on reducing greenhouse gas (GHG) emissions in road transportation, house heating, agricultural activities, marine transport etc. This study concentrated on the use of alternative fuels in engine - driven applicat ions of non - road machineries and decentralized energy production . Today, the engines are mainly designed for crude oil derived fuels and liquid renewable fuels are blended with crude oil based fuels to fulfill the requirements of renewable energy usage. Du e to the environmental reasons on one hand and to the agricultural needs, on the other hand , different blends of bio - and fossil fuels are becoming more popular. In Europe, the maximum FAME content in diesel fuel is 7 vol% according to the EN 590:2013 but higher percentages are also available and targeted around the world. For example in the United States, the 20% blend fraction is becoming more common. For these reasons, B20 fuels were chosen to be investigated in this study. Special emphasis was put on im proving blending issues since fuel blending may cause some operating risks. The main aim was to research widely the properties of animal - fat based methyl ester (AFME) and B20 fuel blend produced from it. AFME is a waste based fuel and produced in Ostroboth nia region, Finland. The aim was to find out in which engine applications the fuels are feasible and investigate if the fuels fit in the quality of automotive fuel Standards. According to the results, AFME is a feasible option to increase self - sufficient e ne rgy production in Ostrobothnia.