Sirvi Autor "Damasceno, F.A." järgi

Nüüd näidatakse 1 - 20 20

Airflow profile study of a compost dairy barn using a low-cost 3D-printed anemometer network
(2020) Vega, F.A.O.; Rios, A.P.M.; Damasceno, F.A.; Saraz, J.A.O.; Nascimento, J.A.C.
Mechanical ventilation is commonly used for environmental thermal regulation inside closed-field agricultural production systems. Analyzing the air distribution inside these facilities and the correct operation of the fans can be a challenging. This could be determined using cost prohibitive techniques as particle image velocimetry or deploying large wind sensors networks on-site. To avoid this limitation without a lack of measurement accuracy, this research was focused on developing and test a low-cost anemometer network based in low cost propeller’s anemometers, built using fused 3D-printed and open-hardware platforms. Four propeller anemometers with three to six blades were simulated using the 6-DOF method of ANSYS computer fluid dynamics software. Similar results were obtained for all the simulated models with minor differences. Anemometers were tested in an open circuit wind tunnel before to be evaluated in two open compost dairy barn building using high-volume low-speed and low-volume high-speed fans. Data were analyzed by employing contour maps, descriptive statistics and correlation. The results show that the anemometer network determines the fan’s wind profile for wind speeds over 0.7 m s-1 and it was possible to determine the facilities spots with ventilation problems. The proposed anemometer network and methodology are a good alternative to analyze the operating conditions of the tested agricultural facilities and optimize its performance.
Analysis of environmental conditions in two different Compost Bedded Pack Barn systems for dairy cattle
(Estonian University of Life Sciences, 2023) Andrade, R.R.; Tinôco, I.F.F.; Damasceno, F.A.; Valente, D.A.; Oliveira, C.E.A.; Oliveira, V.C.; Rossi, G.; Barbari, M.
The objective of this study was to analyse and compare the thermal environment of dairy cattle facilities in an open compost bedded pack barn (CBP) with natural ventilation and closed CBP (without thermal insulation) and climate control system. The research was conducted in a property located in Zona da Mata, Minas Gerais, Brazil. During the summer and for different periods of the day, the following average environmental variables observed inside the facilities were measured: dry bulb temperature, relative humidity and Temperature and Humidity Index (THI). The results were submitted to an analysis of variance to determine the significance of the variables in the different treatments. It was found that the closed and climate control system CBP promoted greater control of the facility's internal microclimate, registering smaller thermal amplitudes and a greater reduction in the animals' exposure time to stressful thermal conditions, compared to the CBP with natural ventilation. However, during summer afternoons, comfort indices indicated moderate stress. It is concluded that the closed CBP, regarding the analysed variables, indicated potential use, provided that a careful study of the climate of the region is carried out before implementation, the factors related to the ambient conditioning and better insulation of the construction are adjusted. The climatic variables inside the open CBP indicated a high stress condition for the animals, suggesting the placement of positive pressure fans and sprinklers properly distributed in the feed alley, to guarantee benefits to the entire area of the animal housing.
Assessment of a low-cost solar water heating systems in farrowing facilities
(2019) Damasceno, F.A.; Osorio, J.A.; Alves Oliveira, C.E.; Ferraz, P.F.P.; Brandão, L.F.
The objective of this study was to develop a prototype solar heater using alternative materials and then to compare its thermal efficiency against that of two other commercial solar heating systems when heating the floor of piglet housing. To evaluate the thermal heaters, temperature sensors were installed in the inlet and outlet of each floor and the thermal reservoir. The results showed good performance, however the thermal efficiency of the alternative heater was lower than the conventional systems. However, due to the construction of this solar collector with alternative materials its cost was relatively low and its operation is easier than the other conventional heater, therefore this heater is a good alternative to use for small livestock producer.
Assessment of spatial variability of environmental variables of a typical house of laying hens in Colombia: Antioquia state Case
(2020) Ferraz, P.F.P.; Gonzalez, V.C.; Ferraz, G.A.S.; Damasceno, F.A.; Osorio, J.A.S.; Conti, L.
This paper aimed to analyze the magnitude and spatial variability of environmental variables: Temperature and Relative Humidity Index (THI), Radiant Thermal Load (RTL), Globe Temperature and Relative Humidity Index (BGTH) and Enthalpy (H), inside a house for laying hens, in the state of Antioquia (Colombia) during the month of August. A traditional Colombian poultry house with natural ventilation was used. All variables were manually measured at equally spaced 1.0×1.0 m points, totaling 99 data collection points inside the poultry house. Geostatistical techniques were used through semivariogram analysis, and isochore maps were generated through data interpolation by kriging. The semivariogram was fitted by the restricted maximum likelihood method. The used mathematical model was the spherical one. After adjusting the semivariograms, the data were interpolated by ordinary kriging. The semivariograms and the isochore maps allowed identifying the non-uniformity of the spatial distribution of all evaluated variables throughout the poultry house. The results show that THI, RTL, BGTH and, H presented values above the comfort limits in the most significant part of the poultry house during the observed period. It is possible to concluded that the use of natural ventilation alone was not sufficient to guarantee the homeothermy conditions for the layers. Thus, it is suggested that in addition to natural ventilation, secondary modifications should be used to improve farm productivity.
Behavioural and physiological responses of rabbits
(2019) Ferraz, P.F.P.; Ferraz, G.A.S.; Barbari, M.; Silva, M.A.J.G.; Damasceno, F.A.; Cecchin, D.; Castro, J.O.
The profitability of a rabbit farming system must consider the thermal environment that the animal will be exposed during the productive period. The goal of this study was to evaluate the physiological responses and behaviours of 26 New Zealand rabbits during seven days of their lives at three times a day. The experiment was carried out in rabbit house in the Federal University of Lavras at Lavras, Brazil. To characterize the thermal environment sensors were used to measure the dry bulb temperature and relative humidity at 48 points inside the rabbit house, at 6:00 a.m., 12:00 a.m. and 6:00 p.m. In addition, the temperature and humidity index (THI) was calculated. The respiratory rate and the superficial temperature of the rabbits' ears were measured. Behaviour evaluations were monitored in punctual record, with duration of two min/cage. Later an ethogram was made with the main behaviours identified. Similar data of behaviour and data of physiological responses were identified by using Ward’s method of cluster analysis. It was observed the period of 6 a.m. showed more comfortable conditions of THI values than the others analysed. Besides, physiological responses presented better values at 6:00 a.m. in comparison to 12:00 and 6:00 p.m. Furthermore, in general, a similar behaviour was observed in the rabbits at 12:00 and 6:00 p.m., while at 6:00 a.m. was different. But rabbits demonstrated to be more comfortable at 6 a.m. maybe because at this time environment conditions were better than the rest of the day. Besides, it can be observed that rabbits were more active in sunrise and sunset than in the rest of the day.
Comparison between the thermal properties of cement composites using infrared thermal images
(2020) Ferraz, P.F.P.; Mendes, R.F.; Ferraz, G.A.S.; Damasceno, F.A.; Silva, I.M.A.; Vaz, L.E.V.S.B.; Mendes, L.M.; Cecchin, D.; Castro, J.O.
The use of agribusiness residual lignocellulosic fibres can be a good alternative in the development of lignocellulosic composites. The current work aimed to investigate the thermal performance of cement-based composites with lignocellulosic materials: Eucalyptus, sugarcane bagasse, coconut fibre in comparison with commercial gypsum board to be used as internal partitions of the building using infrared thermal images. Three repetitions for each kind of lignocellulosic material were made, and three commercial gypsum boards were used. In the production of the panels, the following parameters were applied: material and cement ratio, 1:2.75; water and cement ratio, 1:2.5; hydration water rate of 0.25; additive, 4% (based on cement mass). The calculations were performed for a nominal panel density of 1,200 kg m- ³. The thermal analysis was performed in a chamber composed of MDP (Medium-Density Particleboard) and with an internal layer of rock wool and the heat source (thermal resistance). For the superficial temperature measurement, a FLIR E75 camera was used to capture the infrared images. When the internal temperature of the chamber stabilized at 50 °C, an infrared thermal image was collected from each side of the composite. Thermal properties were analysed: thermal conductivity, resistivity, resistance, and transmittance. Based on the results, sugar cane cement composites were characterized by higher values of thermal conductivity. Related to thermal resistivity, thermal resistance, and thermal transmittance, only the coconut panel presented similar behaviour to the commercial gypsum board. Thus, cement composite using coconut can be a potential alternative that might solve energy and environmental concerns simultaneously.
Comparison of airflow homogeneity in Compost Dairy Barns with different ventilation systems using the CFD model
(2020) Fagundes, B.; Damasceno, F.A.; Andrade, R.R.; Saraz, J.A.O.; Barbari, M.; Vega, F.A.O.; Nascimento, J.A.C.
In the pursuit of high milk productivity, producers are using confinement systems in order to improve performance and animal welfare. Among the housing systems, the Compost bedded-pack barns (CBP) stand out. In these barns a bedding area is provided inside, where cows move freely. Generally this area is covered with carbon source material (such as sawdust or fine dry wood shavings) which together with manure, thanks a regular mechanically stirring, ensures the aerobic composting process. The ventilation in these facilities has the function of dehumidifying the air, improving the air quality, drying the bedding, improving the thermal comfort conditions of the confined animals. This work aimed at validating a computational model using Computational Fluid Dynamics (CFD) to determine the best homogeneity of airflows generated by different forced ventilation systems used in CBP barns. Two CBP barns were compared with different ventilation systems: high volume low speed (HVLS) and low volume high-speed (LVHS) fans. The results showed that the proposed model was satisfactory to predict the flows generated by both types of fans. It was concluded that the use of HVLS fans produced a more homogeneous airflow when compared to LVHS fans. The use of mechanical ventilation in tropical conditions is necessary for the proper functioning of the system. In this study, the systems used promoted the increase in air speed to levels close to adequate.
Compost barn system and its influence on the environment, comfort and welfare of dairy cattle
(Estonian University of Life Sciences, 2023) Nepomuceno, G.L.; Cecchin, D.; Damasceno, F.A.; Amaral, P.I.S.; Caproni, V.R.; Rossi, G.; Bambi, G.; Ferraz, P.F.P.
The aim of this study was to evaluate the effect of the thermal environment on behavioral and physiological parameters of crossbred cows of different productivity levels confined in a compost barn system. For this, air temperature (Tdb) and relative humidity (RH) data were measured using sensors/registers and wind speed (Vair) was recorded with the aid of an anemometer. Subsequently, these data were used to calculate the Temperature and Humidity Index (THI). Bedding material variables (pH and humidity) were also evaluated. The animals were evaluated for physiological variables (respiratory rate – RR and surface temperature – ST), scores (body condition, locomotion and dirt) and behavior. The analyses were carried out on two groups of cows (Group 1: high production vs. Group 2: medium and low production). The average pH of the bedding material was 8.5, within the recommended range. In the case of the physiological responses of the cows, the respiratory rate (RR) of Group 1 indicated better conditions of thermal comfort in the morning vs. the afternoon. The system was efficient in both groups based on body condition score, indicating favorable conditions for the health of the animals. Regarding the behavioral evaluation, Group 1 and 2 were statistically similar and had the longest rumination times, in relation to the other evaluated behaviors. Regarding active periods, medium production were the most active. Regarding idle time, low production spent more time idle than the other animals.
Compost-bedded pack barns in the state of Minas Gerais: architectural and technological characterization
(2019) Oliveira, V.C.; Damasceno, F.A.; Oliveira, C.E.A.; Ferraz, P.F.P.; Ferraz, G.A.S.; Saraz, J.A.O.
Compost bedding pack (CBP) barns have been receiving increased attention as an alternative housing system for dairy cattle. Thus, a systematic investigation of the primary management practices of dairy cattle in CBP barns in the state of Minas Gerais (Brazil) has proven to be of environmental and economic relevance. The aim of this research was to summarize the compost bed data, barn dimension data and to determine the major interactive factors in the success of bed composting from qualitative and quantitative methods. Data for this study was collected from 16 CBP barns, distributed throughout the southern state of Minas Gerais (Brazil) between March 2017 and July 2018. These data were used to describe the building layouts and dimensions, to identify barn management practices, and to characterize the compost bedding material concerning moisture content. The majority of these barns had feed alleys and driveways; overshot ridges with frequent orientation from NE to SW; bedding process and aeration using mechanical tillage. The average bedding moisture content was found to be 36.9 ± 5.2% (w.b.). Based on the information found, it is possible to evaluate that there is still no defined construction pattern, with a high variation of size and technologies employed.
Design and construction of a low-cost remotely piloted aircraft for precision agriculture applications
(2019) Morerira, M.G.; Ferraz, G.A.S.; Barbosa, B.D.S.; Iwasaki, E.M.; Ferraz, P.F.P.; Damasceno, F.A.; Rossi, G.
This study aimed to construct a low cost RPA capable of recording georeferenced images. For the construction of the prototype of a quadcopter type RPA, only essential materials were used to allow stable flight. A maximum total weight of 2 kg was stipulated, including frame weight, electronic components, motors and cameras. The aircraft was programmed using a low-cost microcontroller widely used in prototyping and automation research. An electronic circuit board is designed to facilitate the connection of the microcontroller with the other components of the design. Specific software was used for flight control. The prototype was built successfully, being able to lift stable and controllable flight. However, we still need to acquire equipment and programming components capable of enabling autonomous images and flights. The final cost of the RPA was on average $ 427.00 on average 50% lower than the values found in the Brazilian ARP market ($ 772.81 to $ 1,288.00)
Energetic analysis in compost dairy barn: a case study in southeastern Brazil
(Estonian University of Life Sciences, 2023) Cruz, E.F.L.; Hernández, R.O.; Damasceno, F.A.; Tinôco, I.F.F.; Andrade, R.R.; do Nascimento, J.A.C.; Rossi, G.; Becciolini, V.; Barbari, M.
Energy efficiency aims to optimize the energy consumption of the processes, activities, and machinery of the farm, ensuring the comfort, handling, and safety of the animals. The purpose of the study was to identify the energy consumption demanded by the activities performed at the Compost Dairy Barn facility, located in Itaguara, Minas Gerais, Brazil and to propose energysaving alternatives, applying the Energy Audit Methodology described by the Institute for Energy Diversification and Saving (IDAE in Spanish) from Spain. The energy assessment at the facility allowed us to recognize unnecessary energy expenses in machinery uses, variations in milk production in relation to environmental conditions, waste disposal, and to propose improvement alternatives to reduce energy consumption expenses. Waste production data of 1577.7 kg per year was obtained, which corresponds to the bedding and feeding areas, and 175 kg of waste for the feeding area. Data on the temperature and humidity of the bedding area were collected to determine which of the five months of research is the most demanding in terms of energy. To maintain the animal’s welfare, tracing the times of substantial use of machinery (e.g., fans, tractors) at the facility and calculating Equivalent Temperature Index (ETI) was necessary. The highest percentage consumption of energy was represented by tractors in bedding maintenance and supply, by around 95.03%. The energy analysis of the farm showed a reduction in energy consumption of 45.03%, compared to the initial consumption percentages of the overall livestock activity.
Estimate of manure present in compost dairy barn systems for sizing of manure storage
(2020) Damasceno, F.A.; Monge, J.L.; Nascimento, J.A.C.; Andrade, R.R.; Barbari, M.; Saraz, J.A.O.; Ferraz, G.A.S.
Milk production is increasingly modernized as a result of the growing demand for food around the world. Improvements in livestock facilities are observed, with a large increase in the use of feedlot systems such as the Compost Dairy Barn. Increasing milk production in confinement systems has also raised concerns such as the management of wastes (water, faeces and urine) from the system, which has become one of the most important issues in the intensive dairy farms. The aim of this work was to estimate the amount of manure present in compost dairy barn systems in order to size the manure storage. The study was conducted at four compost dairy barns in southern Minas Gerais, Brazil. These compost barns had different bedding materials and dimensions. In each farm, data on milk yield and quality (daily production, fat and protein content), animal weight and amount of feed ingested by the animals were collected. Total-day manure delivered by the cows in the feeding alley and milking parlour was piled up together and weighed. Based on the results, it was observed that, in the compost dairy barns, only part of the total manure produced per day was delivered in the milking parlour (1.6 and 2.0%) and in the feed alley (27.6 to 49.3%). These results are very important for designers for the proper manure management system design of the dairy farms.
Geostatistics applied to evaluation of thermal conditions and noise in compost dairy barns with different ventilation systems
(2019) Oliveira, C.E.A.; Damasceno, F.A.; Ferraz, P.F.P.; Nascimento, J.A.C.; Ferraz, G.A.S.; Barbari, M.
The objective of this work was to evaluate the spatial distribution of thermal conditions and bed variables in compost dairy barns with different ventilation systems, through the technique of geostatistics. The experiment was conducted in April 2017, in farms located in Madre de Deus, Minas Gerais, Brazil. Three facilities were evaluated with different ventilation systems: natural (NV); mechanical of low volume and high speed (LVHS); and mechanical of high volume and low speed (HVLS). The interior of the premises was divided into 40 meshes equidistant points, in which air temperature, relative humidity and air speed were manually collected. Geostatistics technique was used to assess the spatial dependence of the variables. The results showed the occurrence of dependence and spatial variability of the variables evaluated. Based on thermal comfort indexes, it was concluded that dairy cows were under stress conditions during the hottest hours of the day in the three animal facilities evaluated. The results obtained allow us to understand that the thermal environment is more influenced by the ventilation system adopted.
Lighting and noise levels in compost dairy barns with natural and forced ventilation
(2020) Andrade, R.R.; Tinôco, I.F.F.; Damasceno, F.A.; Barbari, M.; Valente, D.A.; Vilela, M.O.; Souza, C.F.; Conti, L.; Rossi, G.
The housing system, called compost barn, is attracting the interest of several farmers. It allows dairy cows to remain in free movement inside a shed without any containment partitions like those used in freestall barns. In Brazil the compost barns with open sides are very common, but recently some closed barns with climatic control systems have been implemented. The objective of this work was to evaluate and compare lighting and noise levels in an open compost barn with natural ventilation and in a closed compost barn with a climate control system. The latter one is based on tunnel ventilation: inlet of air trough evaporative cellulose panels and exit through fans placed on the opposite wall. Through analysis of the collected data it was observed that the sound pressure recorded inside both analysed buildings did not exceed the ranges of noise discomfort recommended for the rearing of animals. However, the sound pressure amplitude inside the barn with climate control system was greater than in the open barn. The light intensity was significantly lower in the closed barn when compared to the open barn (84.96 and 1,413.58 lx, respectively). The artificial lighting system distributed throughout the closed barn was not sufficient to maintain brightness within the recommended range for lactating cows. In addition, it was found that in the closed building with forced ventilation, the highest brightness values are located near the exhaust fans.
Principal components in the study of soil and plant properties in precision coffee farming
(2019) Ferraz, G.A.S.; Ferraz, P.F.P.; Martins, F.B.; Silva, F.M.; Damasceno, F.A.; Barbari, M.
In this work, a principal component analysis was performed to evaluate the possibility of discarding obsolete soil and plant variables in a coffee field to eliminate redundant and difficult-to-measure information in precision coffee farming. This work was conducted at Brejão Farm in Três Pontas, Minas Gerais, Brazil, in a coffee field planted with 22 ha of Topázio cultivar. The evaluated variables were the yield, plant height, crown diameter, fruit maturation index, degree of fruit maturation, leafing, soil pH, available phosphorus (P), remaining phosphorus (Prem), available potassium (K), exchangeable calcium (Ca2+), exchangeable magnesium (Mg2+), exchangeable acidity (Al3+), potential acidity (H + Al), aluminium saturation (N(Al)), potential CEC (CECp), actual CEC (CECa), sum of bases (SB), base saturation (BS) and organic matter (OM). The data were evaluated by a principal component analysis, which generated 20 components. Of these, 7 representing 88.98% of the data variation were chosen. The variables were discarded based on the preservation of the variables with the greatest coefficients in absolute values corresponding to the first component, followed by the variable with the second highest absolute value corresponding to the second principal component. Based on the results, the variables V, OM, fruit maturity index, plant height, yield, leafing and P were selected. The other variables were discarded.
Spatial distribution of thermal variables, acoustics and lighting in compost dairy barn with climate control system
(2019) Damasceno, F.A.; Oliveira, C.E.A.; Ferraz, G.A.S.; Nascimento, J.A.C.; Barbari, M.; Ferraz, P.F.P.
The main objective of this research was to evaluate the spatial distribution of the thermal variables, acoustics and lighting in climate controlled compost dairy barn. The experiment was conducted in October 2017, in a farm located in the west of Minas Gerais state, Brazil. For the study, the interior of the animal facility was divided into 120 meshes equidistant points, in which air temperature (tdb), relative humidity (RH), noise, illuminance, and air speed (Vair) were manually collected. The technique of geostatistics was used to evaluate the distribution and spatial dependence of variables. Spatial distribution maps showed the occurrence of high variability of attributes and content within the animal facility. Thermal environment variables showed alert situations throughout practically the entire facility. The noise and luminance levels were within the recommended values.
Spatial variability of litter temperature, relative air humidity and skin temperature of chicks in a commercial broiler house
(2019) Ferraz, P.F.P.; Ferraz, G.A.S.; Schiassi, L.; Nogueira, V.H.B.; Barbari, M.; Damasceno, F.A.
The thermal environment inside a broiler house has a great influence on animal welfare and productivity during the production phase. Among the importance of the chicken litter is the function of absorbing moisture, provide thermal insulation and provide a soft surface for broilers. The skin temperature is an important physiological parameter to quantify the thermal comfort of animals, its variations may occur as a function of thermal variables. So, the aim of this work was to analyse the magnitude and spatial variability of chicken litter temperature and relative humidity of the air and to correlate them with the spatial distribution of chicks’ skin surface temperature throughout the broiler house during the 7th, 14th and 21st days of the chicks’ life, using geostatistical techniques. The experiment was performed in a commercial broiler house located in the western mesoregion of Minas Gerais, Brazil, where 28,000 male Cobb chicks were housed. The heating system consisted of an industrial indirect-fired biomass furnace. The heated air was inflated by an AC motor, 2,206 W of power, 1,725 RPM. Geostatistical techniques were used through semivariogram analysis and isochore maps were generated through data interpolation by kriging. The semivariogram was fitted by the restricted maximum likelihood method. The used mathematical model was the spherical one. After fitting the semivariograms, the data were interpolated by ordinary kriging. The semivariograms along with the isochore maps allowed identifying the non-uniformity of spatial distribution of the broiler litter temperature throughout the broiler house for 3 days of chicks’ life. It was observed that skin surface presented a positive correlation with the litter temperature and a negative correlation with the air humidity. The semivariograms along with the isochore maps allowed identifying the non-uniformity of spatial distribution of the litter temperature, air humidity and skin temperature of chicks throughout the broiler aviary for the three days. In addition, the use of geostatistics and distribution maps made possible to identify different environmental conditions in regions inside the broiler house that may harm the development of chicks.
Spatial variability of soil fertility attributes and productivity in a coffee crop farm
(2019) Ferraz, G.A.S.; Avelar, R.C.; Bento, N.L.; Souza, F.R.; Ferraz, P.F.P.; Damasceno, F.A.; Barbari, M.
Coffee cultivation is of great importance to Brazilian agribusiness, as coffee occupies extensive production areas and is one of the most exported Brazilian products. To maintain coffee production numbers, productive techniques must be adopted that optimize productive system use. The objective of this work was to apply geostatistical techniques in the evaluation of soil fertility attributes to construct maps of variability in soil fertility parameters and the productivity of a coffee crop in the municipality of Monte Carmelo, Minas Gerais (MG), Brazil. The work was developed with coffee of the cultivar Mundo Novo 379/19, and 19 sample points were georeferenced in Universal Transverse Mercator coordinates. Spatial dependence of the fertility and productivity parameters was analysed via classic semivariogram fitting and interpolation by ordinary kriging using the statistical computer system, R. All parameters evaluated showed high degrees of spatial dependence. The attribute values varied along the sampling points, except for the sodium (Na) contents, which had similar values in all samplings. The studied parameters ranged from 80 to 200 metres. It is conclusion, the use of productivity maps linked to soil chemical attributes can be useful for determining the occurrence of variable productivity rates throughout the area, allowing the adoption of corrective practices for subsequent crops and thus making the maps very useful tools for producers.
Thermal comfort assessment in a typological non-isolated maternity pig sheds with different types of farrowing systems
(2021) Osorio, J.A.; González, V.; Ferraz, P.F.P.; Ferraz, G.A.S.; Damasceno, F.A.
Swine facilities in tropical climates, especially the maternity, have worked with typological systems that have been little studied to determine the influence of the type of farrowing on microenvironmental conditions and its effect on both the sows and the piglets' physiological parameters. Therefore, the aim of the research was evaluate the thermal environment (Temperature Humidity Index - THI and Radiant Thermal Load - RTL) and its influence on some physiological parameters (respiratory frequency - RF and rectal temperature - TRectal) in the sows and piglets in two different types of farrowing systems (Traditional and Slatted), in a typological swine facility located in tropical climates in Colombia. The findings showed that in the two systems, both for sows and piglets, the type of farrowing system did not generate significant differences in the physiological responses RF and TRectal. Also, the RTL did not show significant differences in the two types of farrowing system at the piglets and the sows’ level, without exceeding the maximum allowed levels. Temperature-Humidity Index was above the threshold during all experimental time, being slightly higher at the piglets' level with Slatted systems. These results show that the type of floor has little impact on the conditions of animal thermal comfort at the sows and piglets’ level. However, variables like low-temperature, low radiant energy exchange, and high humidity, which were found mainly at the piglets’ level, could have the highest incidence for not achieving a suitable microenvironment. This means that almost all Colombian pig farming facilities require a redesign of their farrowing system to guarantee better thermal conditions for both piglets and sows.
Use of compost from a compost barn installation as organic fertilizer
(Estonian University of Life Sciences, 2024) Laurindo, G.M.; Ferraz, G.A.S.; Damasceno, F.A.; Ferraz, P.F.P.; Neto, P.C.; Castro, R.P.; Silva, J.X.; Barbari, M.; Becciolini, V.
Organic fertilization is a profitable option and an environmentally correct alternative. The compost barn confinement system generates an organic material that can be applied to fertilize crops used to produce food for dairy cattle. This work objective is to evaluate the use of this material as an organic fertilizer. For the tests, sunflowers were planted in 15 L pots made up of ¾ soil and ¼ sand, kept in a greenhouse and four doses of fertilizer were tested (0, 5, 25 and 125 g/pot), using organic compost generated by a compost barn with Holstein dairy cows. The tests showed positive results for plant growth and development and for grain production for all doses, with a significant difference only for the 125 g dose, which presented an average number of leaves of 15.96, stem diameter of 12.5 mm and thousand seed weight of 28.63 g. It was found that there was greater plant growth and greater grain filling with an increase in the fertilizer dose, proving the positive effects on the plant of using organic compost from a compost barn.

Sirvi Autor "Damasceno, F.A." järgi

Tulemused lehekülje kohta

Sorteerimisvalikud