Andmebaasi logo

2017, Vol. 15, No. 4

Selle kollektsiooni püsiv URIhttp://hdl.handle.net/10492/5358

Sirvi

Sirvi 2017, Vol. 15, No. 4 Autor "Čedík, J." järgi

Nüüd näidatakse 1 - 3 3
  • Pisipilt
    Kirje
    Comparison of mechanical and electric drive of mulcher
    (2017) Pexa, M.; Čedík, J.; Kumhála, F.; Pražan, R.
    The contribution is focused on comparison of mechanical and electric drive of mulcher with vertical axis of rotation by means of mathematical model. The mulcher has working width of 6 m and it is usually aggregated with tractor of minimal power of 150 kW. On the test plot the torque and power transferred trough the tractor PTO, fuel consumption and the production of gaseous emissions components were monitored. This field measurement served as a basis for modelling as well as measured complete characteristics of the combustion engine of the tractor John Deere 7930. As a main base for the modelling the record of real operation of the tractor with mulcher was used. Then, in the software product MathCad the operation of the tractor with mechanical and electrical drive of the mulcher was modelled. In the case of the electrical drive of the mulcher the tractor with internal combustion engine, connected to generator was taken into consideration. Due to overall lower efficiency of the electrical drive with generator, worse values of the fuel consumption and emissions production in comparison with mechanical drive were reached in case of electric drive. At hypothetical use of batteries (100% electro-powered tractor) and when the energy mix at Czech Republic is taken into consideration, it is possible to reach the quarter values of emissions production in comparison with combustion engine.
  • Pisipilt
    Kirje
    Effect of rake angle and cutting speed on energy demands of mulcher with vertical axis of rotation
    (2017) Čedík, J.; Pexa, M.; Pražan, R.
    The contribution deals with the reduction of agriculture energy demands. For maintenance and treatment of permanent grassland areas, areas left fallow and put to rest the mulching in combination with other workflows (mowing, grazing) is advantageous procedure. As conventional impact grass cutting and chopping is energy demanding procedure, it is proper to reduce the energy demands of such device. In the paper the effect of shape of cutting tool, particularly the rake angle, on energy demands of mulcher with vertical axis of rotation is studied. The effect of cutting speed on energy demands is also verified. The measurement was performed using mulcher MZ 6000 made by Bednar FMT Ltd. with working width of 6 m and three rotors. During the measurement the test rides using the cutting tools with different rake angle and cutting speeds of 105m s-1 , 89 m s-1 and 79 m s-1 were performed. The rake angle of cutting tools were chosen 0°, 15° and 25°. The test area was pasture with permanent grassland. During the measurement the torque and power, transferred through PTO to the machine, fuel consumption and GPS coordinates were measured. From each test ride the samples of grass matter were taken in order to determine the yield and moisture content. It was found that increase of the rake angle up to 25° and decrease of the cutting speed resulted in decrease of the power requirement of the mulcher.
  • Pisipilt
    Kirje
    Influence of shape of cutting tool on pressure conditions in workspace of mulcher with vertical axis of rotation
    (2017) Čedík, J.; Chyba, J.; Pexa, M.; Petrásek, S.
    Nowadays there is laid great insistence on work efficiency improvement. This effort also affects the construction of mowers such as mulchers. Mulching with a vertical axis of rotation is very energy demanding work operation mainly, due to high energy losses. These energy losses, but also the quality of work, are influenced by the airflow and associated conditions of pressure inside the workspace of mulcher. Airflow in the workspace ensures repetitious contact of the truncated forage crops with the cutting edge tool and thus ensures crushing of aboveground parts of plants. The paper deals with the influence of the cutting tool shape on the mulcher’s inside workspace pressure conditions with the vertical axis of rotation. The influence of the trailing edge angle and rake angle on the pressure profile in the mulcher’s workspace with dependence on the rotor speed was examined. Measurements were performed on a laboratory single rotor mulcher model. It was found that in the mulcher’s workspace the vacuum is formed by virtue of the rotary movement of the cutting tools wherein the vacuum increases with rotor speed. The maximum measured vacuum was about 2.4 kPa and from the centre of the rotor towards its circumference almost linearly decreases. Furthermore, it was found that with decreasing trailing edge angle and with increasing rake angle the maximum vacuum decreases. When reducing the angle of the trailing edge from 45° to 25° led to reduction of vacuum of about 0.3 kPa (12.6%).